Open Access
Issue
Mechanics & Industry
Volume 17, Number 7, 2016
STANKIN: Advanced scientific studies and research in Mechanical Engineering
Article Number 717
Number of page(s) 9
DOI https://doi.org/10.1051/meca/2016085
Published online 30 December 2016
  1. F. Han, Li. Chen, D. Yu, X. Zhou, Basic study on pulse generator for micro-EDM, Int. J. Adv. Manuf. Technol. 335 (2007) 474–479 [CrossRef] [Google Scholar]
  2. N. Ojha, F. Zeller, C. Mueller, H. Reinecke, Analyzing the Electrical Pulses Occurring during EDM of Non-Conductive Si3N4 Ceramics, Key Eng. Mater. 651-653 (2015) 659–664 [CrossRef] [Google Scholar]
  3. A. Centeno, V.G. Rocha, B. Alonso, A. Fernández, C.F. Gutierrez-Gonzalez, R. Torrecillas, A. Zurutuza, Graphene for tough and electroconductive alumina ceramics, J. Eur. Ceramic Soc. 3315 (2013) 3201–3210 [CrossRef] [Google Scholar]
  4. S.N. Grigoriev, M.P. Kozochkin, F.S. Sabirov, A.A. Kutin, Diagnostic Systems as Basis for Technological Improvement, Procedia CIRP: Fifth Cirp Conference on High Performance Cutting. 1 (2012) 599–604 [Google Scholar]
  5. H.-P. Schulze, Problems of the processing accuracy for electro-erosion and electro-chemical machining processes, Int. J. Mater. Forming 2 (2009) 641–644 [CrossRef] [Google Scholar]
  6. M.A. Volosova, A.A. Okunkova, D.E. Povolotskiy, P.A. Podrabinnik, Study of electrical discharge machining for the parts of nuclear industry usage, Mechanics Industry 167 (2015) 706 [CrossRef] [EDP Sciences] [Google Scholar]
  7. A.N. Porvatov, M.P. Kozochkin, S.V. Fedorov, A.A. Okunkova, About possibility of vibroacoustic diagnostics of electrical discharge machining and characterization of defects, Mechanics Industry 167 (2015) 707 [CrossRef] [EDP Sciences] [Google Scholar]
  8. A. Centeno, V.G. Rocha, B. Alonso, A. Fernández, C.F. Gutierrez-Gonzalez, R. Torrecillas, A. Zurutuza, Graphene for tough and electroconductive alumina ceramics, J. Eur. Ceram. Soc. (33) (2013) 3201–3210 [Google Scholar]
  9. N. Taniguchi, Current Status in, and Future Trends of, Ultraprecision Machining and Ultrafine Materials Processing, CIRP Annals – Manuf. Technolo. 322 (1983) 573–582 [CrossRef] [Google Scholar]
  10. V.V. Molodtsov, A.A. Okunkova, P. Yu Peretyagin, Manufacture of graphite electrodes for the electrospark machining of complex high-precision components, Russian Eng. Res. 32 7 (2012) 550–552 [CrossRef] [Google Scholar]
  11. M. Kozochkin, A. Porvatov, F. Sabirov, Vibration Testing of Technological Processes in Automated Machining Equipment, Measurement Techniques 5612 (2014) 1414–1420 [CrossRef] [Google Scholar]
  12. S.N. Grigor’ev, M.P. Kozochkin, S.V. Fedorov, A.N. Porvatov, A.A. Okun’kova, Study of Electroerosion Processing by Vibroacoustic Diagnostic Methods, Measurement Techniques (2015) 878–884 [Google Scholar]
  13. T. Masuzawa, H.K. Tönshoff, Three-dimensional micromachining by machine tools, CIRP Annals - Manuf. Technol. V 462 (1997) 621–628 [CrossRef] [Google Scholar]
  14. M. Benedetti, D. Bortoluzzi, C. Zanoni, Non-linear Mechanical Behaviour of Metallic Micro-wires under Dynamic Axial Loads, Experimental Mech. 523 (2012) 215–228 [CrossRef] [Google Scholar]
  15. B. Mei, J. Lucas, S. Holé, I. Lamarque, N. Chéron, Excitation Mode Influence on Vibrating Wire Sensor Response, Experimental Mech. 562 (2015) 331–338 [Google Scholar]
  16. M. Kozochkin, A. Porvatov, Effect of adhesion bonds in friction contact on vibroacoustic signal and autooscillations, J. Friction and Wear 355 (2014) 389–395 [CrossRef] [Google Scholar]
  17. M.P. Kozochkin, A.N. Porvatov, F.S. Sabirov, Vibration Testing of Technological Processes in Automated Machining Equipment, Measurement Techniques 56 12 (2014) 1414–1420 [CrossRef] [Google Scholar]
  18. M.P. Kozochkin, A.N. Porvatov, Estimation of Uncertainty in Solving Multi-Parameter Diagnostic Problems, Measurement Techniques 582 (2015) 173–178 [CrossRef] [Google Scholar]
  19. L. Pang, A. Hosseini, H.M. Hussein, I. Deisab, H.A. Kishawy, Application of a new thick zone model to the cutting mechanics during end-milling, Int. J. Mech. Sci. 96-97 (2015) 91–100 [CrossRef] [Google Scholar]
  20. A. Okunkova, P. Peretyagin, A. Seleznyov, S.V. Fedorov, M. Kozochkin, Characterization of materials’ defects after electrical discharge machining and research into their technological parameters using vibroacoutstic diagnostics, Adv. Mater. Lett. 77 (2016) 100–150 [Google Scholar]
  21. A. Mohammadi, A.F. Tehrani, A. Abdullah, Investigation on the effects of ultrasonic vibration on material removal rate and surface roughness in wire electrical discharge turning, Int. J. Adv. Manuf. Technol. 705 (2014) 1235–1246 [CrossRef] [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.