Articles citing this article

The Citing articles tool gives a list of articles citing the current article.
The citing articles come from EDP Sciences database, as well as other publishers participating in CrossRef Cited-by Linking Program. You can set up your personal account to receive an email alert each time this article is cited by a new article (see the menu on the right-hand side of the abstract page).

Cited article:

This article has been cited by the following article(s):

Investigation, modeling, and optimization of cutting parameters in turning of gray cast iron using coated and uncoated silicon nitride ceramic tools. Based on ANN, RSM, and GA optimization

Aissa Laouissi, M. A. Yallese, A. Belbah, S. Belhadi and A. Haddad
The International Journal of Advanced Manufacturing Technology 101 (1-4) 523 (2019)
DOI: 10.1007/s00170-018-2931-8
See this article

Design optimization for minimum technological parameters when dry turning of AISI D3 steel using Taguchi method

Oussama Zerti, Mohamed Athmane Yallese, Riad Khettabi, Kamel Chaoui and Tarek Mabrouki
The International Journal of Advanced Manufacturing Technology 89 (5-8) 1915 (2017)
DOI: 10.1007/s00170-016-9162-7
See this article

Modeling and optimization in dry face milling of X2CrNi18-9 austenitic stainless steel using RMS and desirability approach

Abdel-Ali Selaimia, Mohamed Athmane Yallese, Hamza Bensouilah, et al.
Measurement 107 53 (2017)
DOI: 10.1016/j.measurement.2017.05.012
See this article

Comparative assessment of cooling conditions, including MQL technology on machining factors in an environmentally friendly approach

Mourad Nouioua, Mohamed Athmane Yallese, Riad Khettabi, Salim Belhadi and Tarek Mabrouki
The International Journal of Advanced Manufacturing Technology 91 (9-12) 3079 (2017)
DOI: 10.1007/s00170-016-9958-5
See this article

Comparative assessment of two ceramic cutting tools on surface roughness in hard turning of AISI H11 steel: including 2D and 3D surface topography

A. Khellaf, H. Aouici, S. Smaiah, et al.
The International Journal of Advanced Manufacturing Technology 89 (1-4) 333 (2017)
DOI: 10.1007/s00170-016-9077-3
See this article

Predictive modeling and multi-response optimization of technological parameters in turning of Polyoxymethylene polymer (POM C) using RSM and desirability function

Amel Chabbi, Mohamed Athmane Yallese, Ikhlas Meddour, et al.
Measurement 95 99 (2017)
DOI: 10.1016/j.measurement.2016.09.043
See this article

Cutting parameters effects on the machining of two high density polyethylene pipes resins

Mounia Kaddeche, Kamel Chaoui and Mohamed Athmane Yallese
Mechanics & Industry 13 (5) 307 (2012)
DOI: 10.1051/meca/2012029
See this article

EXPERIMENTAL INVESTIGATION AND PERFORMANCE ANALYSES OF CBN INSERT IN HARD TURNING OF COLD WORK TOOL STEEL (D3)

H. Bouchelaghem, M. A. Yallese, T. Mabrouki, A. Amirat and J. F. Rigal
Machining Science and Technology 14 (4) 471 (2010)
DOI: 10.1080/10910344.2010.533621
See this article

Modeling and optimization of turning process parameters during the cutting of polymer (POM C) based on RSM, ANN, and DF methods

A. Chabbi, M.A. Yallese, M. Nouioua, et al.
The International Journal of Advanced Manufacturing Technology 91 (5-8) 2267 (2017)
DOI: 10.1007/s00170-016-9858-8
See this article

Comparative study of the performance of coated and uncoated silicon nitride (Si3N4) ceramics when machining EN-GJL-250 cast iron using the RSM method and 2D and 3D roughness functional parameters

A. Laouissi, M. A. Yallese, A. Belbah, A. Khellaf and A. Haddad
Journal of the Brazilian Society of Mechanical Sciences and Engineering 41 (5) (2019)
DOI: 10.1007/s40430-019-1708-9
See this article

Coated CBN cutting tool performance in green turning of gray cast iron EN-GJL-250: modeling and optimization

Salim Chihaoui, Mohamed Athmane Yallese, Salim Belhadi, et al.
The International Journal of Advanced Manufacturing Technology 113 (11-12) 3643 (2021)
DOI: 10.1007/s00170-021-06820-1
See this article

Modeling and Optimization of Cutting Parameters When Turning EN-AW-1350 Aluminum Alloy

F. Khrouf, H. Tebassi, M.A. Yallese, K. Chaoui and A. Haddad
International Journal of Applied Mechanics and Engineering 27 (2) 124 (2022)
DOI: 10.2478/ijame-2022-0024
See this article