Open Access
Issue
Mechanics & Industry
Volume 18, Number 5, 2017
Article Number 511
Number of page(s) 10
DOI https://doi.org/10.1051/meca/2017039
Published online 05 December 2017
  1. Y. Fu, L. Jia, Y. Qin, J. Yang, Product function correntropy and its application in rolling bearing fault identification, Measurement 97 (2017) 88–99 [CrossRef] [Google Scholar]
  2. M.J. Pearson, L.M. Grover, J.M. Lord, S.W. Jones, E.T. Davis, Bearings in hip arthroplasty: joint registries vs. precision medicine, HSS J. 13 (2017) 20–27 [CrossRef] [PubMed] [Google Scholar]
  3. A.V. Korolev et al., Influence of assembly conditions on the static load capacity of thrust ball bearings, Russ. Eng. Res. 37 (2017) 82–85 [CrossRef] [Google Scholar]
  4. D.-J. Cheng, J.-H. Park, J.-S. Suh, S.-J. Kim, C.-H. Park, Effect of frictional heat generation on the temperature distribution in roller linear motion rail surface, J. Mech. Sci. Technol. 31 (2017) 1477–1487 [CrossRef] [Google Scholar]
  5. S. Sundar, J.T. Dreyer, R. Singh, Estimation of coefficient of friction for a mechanical system with combined rolling-sliding contact using vibration measurements, Mech. Syst. Signal Process. 58 (2015) 101–114 [CrossRef] [Google Scholar]
  6. P. Šperka, I. Křupka, M. Hartl, The behavior of surface roughness in EHL contact under small slide to roll ratios, Tribol. Lett. 47 (2012) 357–366 [CrossRef] [Google Scholar]
  7. E. Ciulli, K. Stadler, T. Draexl, The influence of the slide-to-roll ratio on the friction coefficient and film thickness of EHD point contacts under steady state and transient conditions, Tribol. Int. 42 (2009) 526–534 [CrossRef] [Google Scholar]
  8. X. Zhang, Z. Li, J. Wang, Friction prediction of rolling-sliding contact in mixed EHL, Measurement 100 (2017) 262–269 [CrossRef] [Google Scholar]
  9. J.P. Srivastava, M.V. Ravi Kiran, P.K. Sarkar, V. Ranjan, numerical investigation of ratchetting behaviour in rail steel under cyclic rolling-sliding contact, Procedia Eng. 173 (2017) 1130–1137 [CrossRef] [Google Scholar]
  10. J. Zhou, L. Zhu, X. Chen, P. Zhang, X. Liu, Design of an accelerated pure rolling contact fatigue testrig for bearing ball with three contact points, China, Mech. Eng. 15 (2004) 572–574 [Google Scholar]
  11. Y. Shimizu, H.A. Spikes, The influence of slide-roll ratio on ZDDP tribofilm formation, Tribol. Lett. 64 (2016) 19 [CrossRef] [Google Scholar]
  12. Z. Liu, A. Neville, R.L. Reuben, Analyzing elastic-plastic real rough surface contact in running-in, Tribol. Trans. 44 (2001) 428–436 [CrossRef] [Google Scholar]
  13. C.K.P. Vallabh, C. Cetinkaya, Adhesion distribution on the surface of a single microparticle, Appl. Phys. Lett. 109 (2016) 121602 [CrossRef] [Google Scholar]
  14. A. Concustell et al., Severe plastic deformation of a Ti-based nanocomposite alloy studied by nanoindentation, Intermetallics 15 (2007) 1038–1045 [CrossRef] [Google Scholar]
  15. G. Wang, Y. Zhang, S. Du, W. Liu, Study on tribological behavior of steel-brass couples in different atmosphere under high speed and dry sliding, Tribology 27 (2007) 346–351 [Google Scholar]
  16. Z.T. Wu et al., High temperature oxidation behavior and wear resistance of Ti0.53Al0.47N coating by cathodic arc evaporation, Vacuum 135 (2017) 34–43 [CrossRef] [Google Scholar]
  17. K. Yan et al., Investigation on heat dissipation characteristic of ball bearing cage and inside cavity at ultra high rotation speed, Tribol. Int. 93 (2016) 470–481 [CrossRef] [Google Scholar]
  18. D. Zeng et al., Influence of solid solution strengthening on spalling behavior of railway wheel steel, Wear 372 (2017) 158–168 [CrossRef] [Google Scholar]
  19. S. Wen, P. Huang, Tribology fundamental, Tsinghua University Press, Beijing, 2002 [Google Scholar]
  20. Y. Yang, L. Huang, Y. Shi, Adhesion suppresses atomic wear in single-asperity sliding, Wear 352 (2016) 31–41 [CrossRef] [Google Scholar]
  21. C. Zhou, Y. Ou, H. Feng, Z. Chen, Investigation of the precision loss for ball screw raceway based on the modified Archard theory, Ind. Lubr. Tribol. 69 (2017) 166–173 [CrossRef] [Google Scholar]
  22. A. Nieto, J. Kim, O.V. Penkov, D.-E. Kim, J.M. Schoenung, Elevated temperature wear behavior of thermally sprayed WC-Co/nanodiamond composite coatings, Surf. Coat. Technol. 315 (2017) 283–293 [CrossRef] [Google Scholar]
  23. K. Rajesh, P. Braham, A. Sethuramiah, A systematic methodology to characterise the running-in and steady-state wear processes, Wear 252 (2002) 445–453 [CrossRef] [Google Scholar]

Current usage metrics show cumulative count of Article Views (full-text article views including HTML views, PDF and ePub downloads, according to the available data) and Abstracts Views on Vision4Press platform.

Data correspond to usage on the plateform after 2015. The current usage metrics is available 48-96 hours after online publication and is updated daily on week days.

Initial download of the metrics may take a while.